LanBulo
← Back to LanBulo

Gauge & Swatch Guide

Gauge is how many stitches and rows you work in a set length. Match the pattern's gauge and the finished piece fits. Miss it and a sweater meant for you can fit someone else.

How to swatch

A swatch is a test square in the yarn, needles and stitch pattern of your project. It takes an hour and saves you from ripping out a sleeve.

  1. Use the real materials. Pick the yarn from your project, ideally the same dye lot, and the needle type and size the pattern names. If you plan to change needles, swatch with the ones you will use.
  2. Cast on enough stitches. Take the pattern's stitches over 10 cm (4 in) and add 8 to 10 more for borders. The swatch should end up at least 15 cm (6 in) wide, and 20 cm (8 in) is better.
  3. Work in the stitch pattern. If the pattern is in stockinette, swatch in stockinette. For a cable or lace pattern, work the full repeat. Put 3 to 4 garter stitches at each edge so the sides stay flat and out of your count.
  4. Work it the way the project is worked. For a project worked in the round, swatch in the round or carry the yarn across the back so you only knit on the right side. Many knitters purl more loosely than they knit, so a flat swatch can read looser than the round version.
  5. Make it tall enough. Work at least 15 cm (6 in), then bind off loosely. A bind off that pulls in will distort the top edge.
  6. Wash and block like the finished piece. Soak, press out the water, and dry it flat the same way you will care for the garment. Measure only when it is fully dry. Wool and many plant fibers change a lot after a wash.
10 cm / 4 in
Measure in the middle, inside the dashed zone. The edges curl and pull, so keep them out of the count.

How to measure

Gauge is given over 10 cm or 4 in, for stitches across and for rows up. Measure both. Stitches decide the width of the piece. Rows decide the length.

  1. Lay the swatch flat. Put it on a table and smooth it with your hand. Do not stretch it and do not let it relax into a crumple. Measure it as it sits.
  2. Mark 10 cm (4 in) in the middle. Place a ruler across the centre and push in a pin at 0 and at 10 cm. Stay away from the borders.
  3. Count stitches between the pins. In stockinette each stitch is a small V. Count them across one row and include half stitches. A count of 21.5 is a real answer and it matters.
  4. Count rows the same way. Turn the swatch and count up one column of Vs between two pins 10 cm apart. In stockinette, one V is one row.
  5. Check a second spot. Measure again at another place on the swatch. If the two counts differ by more than half a stitch, average them or make a bigger swatch.
  6. Write it down. Save the stitch count, row count, needle size, yarn and how you washed it. Next project in the same yarn, you can skip the swatch.
Quick reference
Quick referenceMetricImperial
Standard gauge span10 cm4 in
Per-unit gaugest / cmst / in
Conversion1 in = 2.54 cm10 cm = 3.94 in
Minimum swatch15 cm6 in

If your gauge is off

Start with stitch gauge, because it controls fit. Change one thing at a time and work a new swatch each time.

  • Too many stitches

    Fabric is tight or small

    You work tighter than the pattern. Go up a needle size, about 0.5 mm (one US size) to start.

  • Too few stitches

    Fabric is loose or large

    You work looser than the pattern. Go down a needle size, about 0.5 mm (one US size) to start.

  • Stitches right, rows off

    Width fits, height does not

    Keep the needles. Work to the length in the pattern and ignore the row count. You may need to adjust shaping to the length you get.

  • Between two sizes

    One is tight, one is loose

    Try a different needle material. Slick metal needles often give looser fabric. Wood and bamboo grip the yarn and often give tighter fabric.

  • On gauge, fabric feels wrong

    Stiff, floppy or see-through

    Trust the fabric. A yarn that only works at a stiff gauge may be the wrong yarn. Try another weight or fibre.

  • Cannot match at all

    Every needle size misses

    Recalculate the pattern with your own gauge, or choose a different yarn. The calculator below shows how far off you are and how many stitches to cast on.

  • Every 0.5 mm of needle size usually shifts gauge by 1 to 2 stitches per 10 cm. It varies with the yarn and stitch pattern, so always swatch again.
  • Round to the needles you own. If the answer is 3.6 mm and you have 3.5 mm and 4 mm, try 3.5 mm first.
  • Gauge drifts. Stress, a long break or a different time of day can change it. Check again after the first 10 cm and after a long pause.
  • One piece at a time. Sleeves, body and edging can need different needles in the same project.

Gauge calculator

Enter your swatch numbers and the pattern's gauge to see how close you are.

Your swatch
Pattern gauge
Plan with your gauge (optional)

Enter your swatch numbers above to see the result.

Related tools & guides