How to block different fibres safely, rescue stained or moth-damaged pieces, and handle common care mishaps.
Always follow the yarn or garment care label first. Test on a swatch or hidden area; for blends use the most restrictive care instructions. Heat symbols here are general guidance, not permission to iron. For valuable or uncertain items, consult a knitwear cleaner.
Shape it now, keep it for years
Blocking relaxes the fibers so stitches even out and the piece dries at the size you want. How you do it depends on the fiber. Heat and agitation are what ruin things, so check the table below before you reach for the iron.
Wet blocking
Best for: wool, cotton, linen, lace and anything that needs a real reshape. It gives the biggest change.
1.If the care label permits wet blocking, fill a basin with cool or lukewarm water and an appropriate yarn wash.
2.Lay the piece in and press it under. Soak 15 to 20 minutes without stirring or rubbing.
3.Lift it out supported with both hands. Press out water, then roll it in a towel and press again.
4.Pin or lay it flat to your target measurements. Let it dry fully, often 12 to 48 hours.
Watch: Never wring. Hot water plus movement felts wool.
Spray blocking
Best for: delicate fibers, small fixes, seams, and yarn whose dye you do not trust to sit in water.
1.Pin the dry piece out to the right shape and size.
2.Mist with a spray bottle of cool water until evenly damp, not dripping.
3.Smooth the surface gently with your palm and leave it to dry flat.
Watch: Mist the whole piece evenly. Patchy wetting leaves water rings, especially on silk.
Steam blocking
Best for: Quick finishing only when the care label explicitly permits steam. Test a swatch first.
1.Pin the piece to shape on a padded surface.
2.Hold a steamer or an iron on its steam setting 2 to 3 cm above the fabric. Do not touch down.
3.Leave it pinned until it is completely cool and dry, then unpin.
Watch: Do not steam acrylic or other synthetics unless the label explicitly permits it. Steam can permanently change acrylic; direct heat can melt synthetics.
Which method for which fiber
Wool
Wet
Yes
Steam
Yes
Spray
Yes
Heat:
●●○
Watch for: Felts with hot water or agitation. Keep the soak lukewarm and still.
Superwash wool
Wet
Yes
Steam
Careful
Spray
Yes
Heat:
●●○
Watch for: Grows a lot when wet. Measure as you pin, not before.
Alpaca & mohair
Wet
Yes
Steam
Careful
Spray
Yes
Heat:
●○○
Watch for: Heavy when wet and prone to growing. Support it when lifting. Pressing flattens the halo.
Cotton
Wet
Yes
Steam
Yes
Spray
Yes
Heat:
●●●
Watch for: Grows when wet and dries slowly. Block to slightly smaller than your target.
Linen
Wet
Yes
Steam
Yes
Spray
Yes
Heat:
●●●
Watch for: Stiff at first. A soak softens it, and steam gives a crisp finish.
Silk
Wet
Careful
Steam
Careful
Spray
Careful
Heat:
●○○
Watch for: Test the dye first. Use cool water, and wet evenly to avoid water rings.
Bamboo, viscose, rayon, tencel
Wet
Careful
Steam
Careful
Spray
Yes
Heat:
●○○
Watch for: Weak and very heavy when wet. Dry flat, never hang, and lift with two hands.
Acrylic
Wet
Yes
Steam
Permanent
Spray
Yes
Heat:
✕ none
Watch for: Water changes little. Steam "kills" it for good, making it limp. Use that on purpose only.
Nylon & polyester
Wet
Yes
Steam
No
Spray
Yes
Heat:
✕ none
Watch for: Direct heat can melt or glaze these fibres. Follow the most restrictive care instruction in a blend, including the yarn label.
●●● Higher heat tolerance in some pure plant fibres; only iron if the care label permits it.
●●○ Moderate heat tolerance; only steam if the care label permits it, never press.
●○○ Low heat tolerance; only permitted steam from at least 5 cm away, in short bursts.
✕ No heat at all
For a blend, follow the most delicate fiber in it. If a yarn label shows an iron symbol with a cross, treat the whole piece as no heat.